Slinky Round
 |
 Ernie Ball 2835 Extra Slinky Round Wound Bass Strings  US $18.49
|
 NWT Guess Ladies Dress S P Exotic Rose Slinky Ties Round Neck w Ribbon US $26.00
|
Ground SOurce Heat Pumps - What your Installer Should be Asking
Unfortunately, with the installation of heat pumps about to explode due to the Renewable Heat Incentive (RHI) and other incentives being offered, the installer market will see a number of unscrupulous companies trying to cash in, even if they have the ‘correct' approvals.
As an aside, there are a number of companies who aren't approved who are more than competent, do an excellent job and have been involved in installing renewable technologies for years and are not MCS approved simply as it can be a difficult and onerous process particularly for one man bands, but that's a different subject. [NB: if you want to benefit from the RHI, you will need to use a MCS accredited installer - ed]
It therefore pays for the client to still do their homework on any potential installer/supplier.
The normal guidelines for entering any contract will apply, such as: references - preferably actually talking to previous clients - ideally ones who have lived with the technology for at least a year; talking to a number of companies to obtain comparable quotes; trade associations, etc.
However you would also expect the installer/supplier to ask you questions, and these questions, or lack of them, should give you an indication of whether the company actually knows what it is talking about.
1. Is the building being insulated to current building standards? This should be one of the first questions the installer/supplier should ask as it will determine whether heat pump technology is right for the building.
2. Will a SAP calculation be available? A Standard Assessment Procedure (SAP) can be used to calculate the size of a heat pump suitable for the property as it takes into account the form, construction and insulation levels of the property. It can also be used to check the insulation levels of the property.
3. What is the overall area of the building to be heated? In the absence of a SAP, the overall area of the building can give an installer/supplier an initial indication of the size of the heat pump required.
4. How is the property being heated? UFH (under floor heating) or radiators? This will determine the efficiency of the heat pump and will impact on your fuel costs and hence payback.
5. How is the domestic hot water (DHW) being heated? Is solar thermal being installed? The heat pump can provide domestic hot water if required, however the installer/supplier needs to be aware of this as it does have an impact on the amount of ground arrays and the equipment supplied. DHW is an additional load on the ground and is all year round so the ground arrays need to be increased, also any hot water cylinders need to have oversized coils due to the lower temperature generated by heat pumps.
6. What is the floor construction of the building? Joisted, beam and block or other? Floor construction can again have an impact on efficiency for example for a joisted underfloor first floor system the flow temperature has to be higher than the magical 35oC always quoted for underfloor, as the heat has to be driven through the floorboards.
7. Is a single or three phase electrical connection available on site? Some manufacturer's single phase heat pumps are limited in size (Kensa can offer a 24kW, which is one of the largest in the market place). Three phase is better as the heat pumps are more efficient and it is a more stable electricity supply but expensive to put in.
8. Is an area roughly twice the area of the property available for the ground arrays? For ground source heat pumps horizontal arrays, i.e. slinkies or straight pipe roughly twice the area to be heated is required for these. If this isn't available then the alternative is boreholes. While equally effective they can be expensive.
9. Has planning permission been obtained? Ground source are a permitted development, but air source currently still require planning permission.
10. Finally be aware of any significant differences for claimed COPs. This should be quoted at standard conditions as laid out by EN14511-2 and should provide a means of comparing like for like. Any other standard will give different figures. In fact COPs from one brand to another should be roughly the same as many will contain similar if not the same key components
To find out more about the right questions your installer should be asking, you can visit the Kensa Heat Pumps website for further information about ground source heat pumps.
About the Author
John Barker-Brown joined Kensa Engineering in Sept 2006 as application manager, ensuring that heat pump technology was applied correctly and advising customers on the best use of this technology. In 2008 he became special projects manager and is now applying his experience to grow Kensa's profile and presence in the heat pump market.
Before Kensa, John spent six years as business development executive for a large International company specialising in the control of industrial fluids. There he specialised in growing market share and finding new opportunities for new products.
